新闻详情

·反应釜设计及配件选择

反应釜网的小编跟大家介绍反应釜设计及配件选择。

确定反应釜

工艺计算的物性数据,进行设备的工艺计算;

(1)确定设备各元件的基本尺寸,确定各元件强度设计参数;进行釜体的计算

(2)筒体容积的设计

(3)筒体长径比的设计

(4)确定筒体的直径和高度及夹套的高度设计

(5)同体容积的校核及夹套高度的确定

(6)筒体厚度的计算及校核

(7)封头厚度和夹套壁厚的计算

(8)釜体及夹套的水压试验及筒体稳定性校核

2 反应釜进行接管的选择及开孔补强计算

(b)进行补强计算

(1)搅拌器的的选型

(2) 搅拌器的参数确定和搅拌器功率的计算

(3)搅拌器的校核

4 反应釜传动装置的计算及选型

(a)电机功率的计算

(b)搅拌轴的设计及机械计算

c)反应釜电动机的选择

(d)减速机的选择

选用零部件附件的结构在满足工艺要求的条件下由受力条件、制造、安装等因素决定其中包括(安装底盖选择、机架的选择、法兰选型、联轴器选型、搅拌轴底轴承选型、搅拌机轴封的选型、密封填料的选择、填料箱的选择)

(1)支座的选型

(2)底座的设计及选型

3.7 绘图及说明书的编写

绘制装配图及各个零件图,并编写说明书。

以上是反应釜网的小编总结的反应釜设计及配件选择,广大朋友们有需要换热器,欢迎来电咨询购买。质量保证,服务一流!

英文:Reaction kettle network of small series with you to introduce the reaction kettle design and accessories selection.

Determine the material properties of the reaction kettle process, and calculate the process of the equipment;

(1) determining the basic dimensions of each component of the apparatus, determining the strength design parameters of each element, the calculation of the kettle body

(2) the design of the volume of the cylinder

(3) the design of tube length diameter ratio

(4) determine the diameter and height of the cylinder and the height of the jacket

(5) the checking of the volume of the body and the height of the clip

(6) calculation and verification of the thickness of the cylinder

(7) the calculation of the thickness of the head and the thickness of the jacket

(8) water pressure test of the kettle body and jacket and the stability of the cylinder

2 reactors over the selection and opening reinforcement calculation

(a) selection (including: feeding tube, thermometer, pressure gauge, air pressure pipe, pressure feed inlet, steam and cooling water inlet and outlet nozzle, air vent nozzle and safety valve nozzle

(b) reinforcement calculation

3 the type design and calculation of the stirring device of the reaction kettle

(1) selection of the agitator

(2) calculation of the parameters of the mixer and the calculation of the power of the mixer

(3) check of the agitator

Calculation and selection of the 4 reaction kettle transmission device

(a) calculation of motor power

(b) design and mechanical calculation of the mixing shaft

C) choice of reaction kettle motor

(d) selection of the reducer

5 reaction kettle parts selection

Selection of accessory parts of the structure to meet the requirements of the process conditions by stress conditions, manufacture, installation and other factors including (install the bottom cover selection, frame, flange type, selection of coupling, stirring shaft bottom selection of bearing type, agitator seal, a sealing filler, a filler box choice)

6 the design and selection of the type and the base of the reaction kettle

(1) selection of bearings

(2) the design and selection of the base

3.7 drawing and instruction manual

Draw assembly drawings and parts drawings, and write instructions.

Above is the reaction kettle network of small series of reaction kettle design and accessories selection, the majority of friends have the need for heat exchanger, welcome to inquire to buy. Quality assurance, service class!

BACK

版权所有:河南省寿泰反应釜有限公司, All rights reserved

地址:河南省三门峡  电话:0398-890603  邮箱: tdzdqp@pandabamboofloor.com